A timber stud partition in a CT6 room
A stud partition is a quick way to split a room in a Herne Bay house without touching the walls on either side. A partition that carries no load from above is a simple job, and it goes up quickly once the timber is on site. This guide counts a partition 3.0 metres long and 2.4 metres high, from the sole plate on the floor to the head plate under the ceiling.
Herne Bay Builders Merchants is the Herne Bay delivery site of Discount Builders Merchants (KENT) LTD, the builders' merchant at Lower Road, Northfleet, DA11 9BB. There is one yard, and orders are placed on www.discountbm.co.uk.

Checking the floor and the ceiling
Before the timber is ordered, find out what the partition stands on. A timber floor takes the sole plate on its joists, while a concrete floor needs a damp proof membrane under the plate, and the timber for the sole changes with it. Find out where the joists above run, too, because the head plate has to fix into them and its position is marked from that.
A partition that carries a load from above is the designer's job. This guide assumes one that carries only its own weight and the boards fixed to it, and any doubt goes to the building control officer before the frame goes up.
Sole and head plates
The sole plate and the head plate are both 100 by 47 mm sawn timber. On a concrete floor the sole is treated, and the head plate can be the same timber for simplicity. Each plate is the length of the partition, which here is 3.0 metres, so each takes its own 4.8 metre length and the offcut is kept.
Mark the line of the sole plate on the floor with chalk, and check it with a square at each end. A partition out of square at its foot pulls every stud out of line, so the plates are where the care is needed.
Studs at 400 mm centres
Studs go at about 400 mm centres from end to end, with a stud at each end of the run. Take the length, divide by 0.4, round up to whole spaces, and add one for the last stud, so a 3.0 metre run takes nine studs.
CLS is planed and untreated, which suits a partition inside a room kept dry. Each stud is one 2.4 metre length, cut to the height less the two plates, so it comes out at about 2.3 metres. Fix each stud to both plates with nails or screws at each end, and check it for plumb as it goes in.
Boarding the frame
Plasterboard is fixed vertically, one sheet at a time, so each 2400 mm board runs the full height of the wall and its edges fall on a stud. Fix the boards from the centre out so they stay flat, and keep each joint on the line of a stud.
Measure the room before the boards are ordered, since a sheet cut short at the ceiling wastes its offcut. Both faces of the partition are boarded, so count both.
Ordering for collection
Collection from the Northfleet yard on Lower Road has no delivery charge, so the plates, the studs and the boards can be fetched together. Delivery to Herne Bay is quoted for each order, and the quote depends on the address and on where the long lengths can be unloaded.
Long timber does not turn tight stairs easily, so measure the route up to the room before the order goes in.
Rules of thumb
| Sole and head plates | 100 by 47 mm sawn timber in 4.8 m lengths. Each 3.0 m plate takes its own length. |
|---|---|
| Studs | CLS 63 by 38 mm at one per 400 mm of wall, rounded up to whole spaces, plus one. |
| Stud length | The 2.4 m length less 94 mm for the two plates, so about 2.3 m a stud. |
| Boards | 2400 by 1200 mm covers 2.88 square metres. Count both faces of the partition. |
| Allowance | A tenth for cuts on the boarding. |
The shop has calculators that turn a measurement into a quantity.
Worked order: A 3.0 metre stud partition in a Herne Bay room
| Product | Quantity | What it is for | Cost |
|---|---|---|---|
| 100x47x4800mm Sawn Treated Timber (4"x2") | 2 at £9.59 | The sole plate and the head plate are each 3.0 m, and each takes its own 4.8 metre length, so two. The 1.8 m offcut from each is kept for a short noggin or a bearer. | £19.18 |
| 63x38x2400mm (3" x 2") CLS Timber | 9 at £3.59 | Studs at about 400 mm centres along 3.0 m: 7.5 spaces, rounded up to eight, plus one, so nine. Each is one 2.4 m length cut to about 2.3 m. | £32.31 |
| Standard Board T/E 2400x1200x12.5mm Plasterboard | 6 at £8.33 | Both faces of the 3.0 m by 2.4 m partition are 14.4 square metres. At 2.88 a board that is 5.0, and a tenth for cuts makes 5.5, so six. | £49.98 |
| Goods | £101.47 | ||
| Collected from Lower Road, Northfleet | £0.00 | ||
| Total ex VAT | £101.47 | ||
| Total inc VAT | £121.76 | ||
Not in this order: Doors and their frames, the ceiling and its joists, any load-bearing timber the drawing calls for, the plaster skim, and the screws and nails, which are a separate order.
The quantities are a starting point for a job of this size. Put the same goods in a basket on www.discountbm.co.uk with your own postcode to see the figure for your order, or send the yard your list.
On the shop today
The products this guide talks about, from the shop's Timber & Sheet Material aisle. Prices last checked .
-
100x47x3000mm Sawn Treated Timber (4"x2")
each
£7.19 inc VAT
£5.99 ex VAT
In the yard
-
89x38x2400mm (4" x 2") CLS Timber
each
£5.75 inc VAT
£4.79 ex VAT
In the yard
-
25 x 38mm Treated Batten 3.6mtr
each
£2.59 inc VAT
£2.16 ex VAT
In the yard
-
100x47x3600mm Sawn Treated Timber (4"x2")
each
£8.63 inc VAT
£7.19 ex VAT
In the yard
-
63x38x2400mm (3" x 2") CLS Timber
each
£4.31 inc VAT
£3.59 ex VAT
In the yard
-
25 x 50mm Treated Batten 3.6mtr
each
£3.41 inc VAT
£2.84 ex VAT
In the yard
-
100x47x4800mm Sawn Treated Timber (4"x2")
each
£11.51 inc VAT
£9.59 ex VAT
In the yard
-
89x38x3000mm (4" x 2") CLS Timber
each
£6.76 inc VAT
£5.63 ex VAT
In the yard
Prices are the shop's prices today. Stock and ordering are on www.discountbm.co.uk.
Timber and sheet materials for CT6 See all Timber & Sheet Material on the shop
Delivery to Herne Bay
- CT6
-
Ask the yard about this district. It is not a shop price.
More guides for Herne Bay
- Matching brick for older houses in CT6 Reading an old brick wall in CT6, sizing a stock-brick patch, and the engineering course under a new damp proof course, worked to one collected order.
- Blocks for a garden wall in CT6 Counting the footing, blocks, sand and cement for a garden wall 4.4 metres long in CT6, from the trench up, with one worked order to collect.
- Shingle for a front garden in CT6 Depth, shingle tonnage and a geotextile membrane for a gravel front garden in CT6, with a worked order to collect from the yard in Northfleet.